Tailgate Flagpole Bracket Guide for Jeep JK JL And BJ40

A tailgate flagpole bracket provides a dedicated rear mounting position for your vehicle flag. The ZYZ holder has a listed length of 31 cm and a 28 mm opening, with applications shown for Jeep JK/JL and the 2024 BJ40.

Choosing the right kit involves more than matching the vehicle name. The bracket needs to suit your tailgate mounting points, accept the flagpole base and leave enough clearance when the tailgate opens. Checking these details before ordering helps avoid a mismatched bracket or a pole that interferes with other rear accessories.

Product Specifications at a Glance

The 31 cm measurement describes the holder, not the height of the flagpole. The 1.1 kg figure is the listed product weight; it is not a maximum load rating. Confirm the mounting kit supplied for your vehicle when ordering.

Choose the Version for Your Vehicle

Jeep JK and JL Fitment

Both JK and JL are listed applications. Provide the exact model, production year and a clear photo of the tailgate mounting area so ZYZ can confirm the correct version and hardware. Listing both vehicles does not establish that every bracket plate or fastener is interchangeable between them.

Also identify any aftermarket tailgate hinges, spare tire carrier or rear accessory panel. These changes can affect mounting space and access even when the vehicle itself is a listed application.

The 2024 BJ40 Application

The product sheet specifically identifies the 2024 BJ40. For an earlier model or another version, send the vehicle details and mounting-area photo for confirmation. Do not extend that model-year listing to every BJ40 tailgate design.

Match the Flagpole to the 28 mm Opening

Measure the outside diameter of the part of the pole that enters the holder. Include any sleeve or cover in that measurement. Then check the insertion depth, the retention method and whether a collar, connector or other base fitting prevents the pole from seating correctly.

A matching nominal diameter is a useful starting point, but the complete base connection still matters. A pole should seat and secure as intended without being forced into the holder. Ask about a compatible sleeve or adapter if the base differs from the specified connection.

For a flagpole sold by its overall height, request the base dimensions separately. The pole height tells you about clearance above the vehicle; it does not tell you whether the lower section fits this holder.

Plan the Tailgate Mounting Position

The installation example places the holder vertically near the outer side of the tailgate, beside a rear light. Use that image to understand the arrangement, then assess the proposed position on your own vehicle.

Check space around the rear light, spare tire, handle and other accessories with the pole installed.

With the vehicle parked, check clearance as the tailgate moves through its intended opening range.

Keep access to the latch and avoid blocking lights, the number plate or the rear camera.

Measure the final installed height and account for overhead clearance before entering covered parking.

An oversized spare tire or separate swing-away carrier can change the available space. Include those details in a fitment request, especially if the current setup differs from the installation photo.

Installation Checks Before Use

Use the instructions for the vehicle-specific kit. A mounted product photo does not establish which factory fasteners are reused or whether a particular version requires drilling.

Check the kit contents and confirm the mounting locations before loosening any vehicle hardware.

Inspect the tailgate and proposed mounting area. Follow the vehicle procedure if installation involves hinge hardware or could affect tailgate alignment.

Install the bracket using the specified hardware, tightening sequence and torque. Avoid substituting bolts simply because they appear to fit.

Insert and secure the compatible flagpole, then check the rear accessories and tailgate movement while parked.

Recheck the bracket and pole retention after the first use and during routine inspections. Correct any movement or loose hardware before further use.

Confirm the permitted pole length, flag size and operating conditions for the complete assembly. A longer pole or larger flag changes the demand on the mount, so bracket dimensions alone cannot establish a safe load or driving speed.

Frequently Asked Questions

Can This Bracket Hold an LED Whip Light

Check the light base against the 28 mm opening and the holder retention method. A threaded stud or a separate quick-release base may need a different connection. Confirm the permitted load and provide a cable route that remains clear as the tailgate moves.

Does the Bracket Reinforce the Spare Tire Carrier

This product is presented as a flagpole bracket. Do not treat it as a tailgate reinforcement kit or assume that it increases the vehicle spare tire capacity.

Is a Flagpole Included

Confirm the contents of the selected kit. The installed photo shows a flagpole in use, but it does not confirm that a pole, flag or adapter is included with every bracket order.

Request the Correct Kit From ZYZ

Send ZYZ your vehicle model and year, a photo of the tailgate, details of any rear accessory changes and the flagpole base dimensions. Include the pole height and flag size so vehicle fitment and pole compatibility can be checked together.

For trade orders, the listed packing quantity is 10 sets per carton. Request current kit contents, carton dimensions and gross weight with your quotation, and specify how many sets you need for each vehicle application.

Publishing Notes

For the site editor only. Do not paste this page into the public article.

Lingdong Fields and Headings

Enter Article Title and Article Summary in their separate fields. Copy the body from A tailgate flagpole bracket to the final quotation paragraph, without the ARTICLE BODY label.

The body uses Heading 2 for main sections and Heading 3 for subsections and FAQ questions. Check that Lingdong preserves those levels after pasting.

Use the actual author or reviewing product specialist and publication date. Add installation experience or test results only when supported by records and original photos.

Image Placement and Alt Text

Use the original product and installation photographs where available. Confirm the photographed vehicle before adding a model name to its alt text. Keep small specification text out of the main cover image.

Internal Links and Product Details

Link ZYZ tailgate flagpole bracket to the actual product page, compatible flagpole to the relevant category and the quotation request to your inquiry page.

Confirm the SKU for each vehicle, compatible years, hole locations, supplied fasteners, retention method and installation instructions before adding more detailed fitment claims.

Add material, coating, load capacity, approved pole lengths or no-drill claims only after checking the current product specification. Keep the 1.1 kg product weight separate from load capacity.